![]() ![]() Horizontal and Vertical Cursors with automatic waveform measurements, and waveform references.Channel Math: add, multiply, invert, and average.Spectrum Analyzer with different windowing options and selectable vertical log and IQ visualization. Gabotronics xscope, Studio muzikore ne tirane, Ath 5b95, Kalendarz pwr 2015/16, Cynthia sheeler nobody wins Bogdan vitas key west, Germanen roman.XY Mode: For plotting Lissajous figures, V/I curves or checking the phase difference between two waveforms.Meter Mode: VDC, VPP and Frequency readout. The XScopes (Xminilab and Xprotolab) are a combination of three electronic instruments: a mixed signal oscilloscope, an arbitrary waveform generator, and a.This project is aimed at producing a GUI framework for using that driver. The node-xscope project was aimed at producing a driver package for a Gabotronics Xminilab oscilloscope module, which should be easy to use in small coffeescript scripts run from the command-line. I have been using one of these on my eurorack rig for a couple of years with good success - see pictures. Advanced Triggering System: Normal / Single / Auto / Free, with many trigger modes adjustable trigger level, and ability to view signals prior to the trigger. A HTML-based GUI for my node-xscope project. This is a small two channel oscilloscope. ![]() The user interface is 4 buttons, and a real pain to use. Arbitrary Waveform Generator with advanced sweep options on all the wave parameters. Ive got one permanently fixed on my breadboard, but I wouldnt reccomend it. Main Features: Mixed Signal Oscilloscope: Simultaneous sampling of 2 analog and 8 digital signals. Arbitrary Waveform Generator with advanced sweep options on all the wave parameters. The only low-cost dual trace with onboard display I know of is the Gabotronics Xscope.Mixed Signal Oscilloscope: Simultaneous sampling of 2 analog and 8 digital signals.The Xprotolab and Xminilab can be plugged directly on a breadboard. The XScopes can also be used as development boards for the AVR XMEGA microcontroller. On my board, I switched these two around, so when the COM port is connected, the red LED turns on.The XScopes are a combination of three electronic instruments: a mixed signal oscilloscope, an arbitrary waveform generator and a protocol sniffer. The XScopes are a combination of three electronic instruments: a mixed signal oscilloscope, an arbitrary waveform generator and a protocol sniffer. The bottom LED (LED1) is the 'Status' LED and is typically red. The top LED (LED2) is the 'Connect' LED for the Bluetooth module, and is typically green. The 3V3 for the module is derived from the 3V3 output on the Xprotolab therefore, it will work whether powered by the DC barrel jack or the USB connector on the Xprotolab. To connect the Bluetooth module, I had to use air wires to connect to the expansion jack on the right of the Xprotolab, since these pins are not broken out anywhere else. To connect these, I used 0.024 inch traces on the top layer, with vias connecting the top and bottom ground planes surrounding them in an attempt to shield the traces. The XScopes are a combination of three electronic instruments: a mixed signal oscilloscope, an arbitrary waveform generator and a protocol sniffer. The BNC jacks are from Sparkfun therefore, the parts used in Eagle are from the Sparkfun library (linked in the GitHub repository below). To make this board, I first created the schematic and board layout, then sent this to OSH Park for production. Two rows of I/O pin headers are used to bring the Xprotolab I/O pins to the edge of the board. In addition, this board also adds a 5V switching regulator so that the Xprotolab can be supplied by a 6.3-30V power supply, as well as a Bluetooth module that allows the wireless use of the Gabotronics Xscope computer interface. The XScopes are a combination of three electronic instruments: a mixed signal oscilloscope, an arbitrary waveform generator and a protocol sniffer. Therefore, this breakout board converts the two analog inputs, arbitrary waveform generator, and trigger pins to BNC jacks. sensors, frequency counters, etc.) or with oscilloscope probes. You can also connect it to your PC and use Gabotronics XScopes software to control the device and view waveforms. However, it is sometimes necessary to use this oscilloscope with other instruments that use BNC connections (i.e. The XMEGA Xprotolab is a convenient mixed-signal oscilloscope (MSO) with an arbitrary waveform generator fitted to a DIP form factor.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |